The compression rings are a bit harder so I bought pliers for them. They were only a few euros and made installing the rings really easy. I just had to make sure the moly faced ring was installed to the top groove and that they were installed the correct side up. This was indicated by a dot on both rings.
Then it was time to insert the pistons to their cylinders. Before the final install, I wanted to check the bearing clearance though. I did that only for the first piston as testing all of them would have been somewhat pointless. First the bearings.
Then pieces of rubber tubing over the bolts to protect the bores.
And installation. I had a cheap ring compressor that I screwed around the piston. I sprayed WD-40 on everything and then tapped the piston in. The compressor unfortunately got stuck a bit and broke as I pulled it out. So much for cheap tools. At least I got the clearance measured with Plastigage again.
As with the main bearings, the result was about 0.002 inches. Acceptable range should be 0.002 - 0.003 inches so I was fine.
I did some reading and apparently the best tool for installing pistons is a tapered aluminium ring that is precision tooled for a single bore size. So I went an bought one by Moroso.
You can only use it for 4.030 inch bore size but I don't think I'll be building another engine any time soon. After pulling the first piston out again, I prepared it and the crankshaft for final install. This meant spreading some assembly lube on the journals and bearings...
...then turning the correct journal to bottom dead center (BDC), oiling the bore, locating the ring gaps and using the tool to tap the piston in. For ring gap positions I used the ones instructed in Millers book.
I have to say that the installation ring was an excellent tool! I did not have a single problem with any of the pistons. They just smoothly slipped in the cylinders. I pushed the piston in until the bearing contacted the journal.
Final step before placing the cap on the rod was checking that the locating tab on all the bearing faced towards the center of the block.
This meant that the rod had been installed correctly on the piston. Everything was OK in that front so I torqued the cap nuts to 24 ft-lbs. And after a few hours of work, all the pistons were in!
Turning the crank was naturally much harder now but everything still moved smoothly so this job was done!
Then it was time to insert the pistons to their cylinders. Before the final install, I wanted to check the bearing clearance though. I did that only for the first piston as testing all of them would have been somewhat pointless. First the bearings.
Then pieces of rubber tubing over the bolts to protect the bores.
And installation. I had a cheap ring compressor that I screwed around the piston. I sprayed WD-40 on everything and then tapped the piston in. The compressor unfortunately got stuck a bit and broke as I pulled it out. So much for cheap tools. At least I got the clearance measured with Plastigage again.
As with the main bearings, the result was about 0.002 inches. Acceptable range should be 0.002 - 0.003 inches so I was fine.
I did some reading and apparently the best tool for installing pistons is a tapered aluminium ring that is precision tooled for a single bore size. So I went an bought one by Moroso.
You can only use it for 4.030 inch bore size but I don't think I'll be building another engine any time soon. After pulling the first piston out again, I prepared it and the crankshaft for final install. This meant spreading some assembly lube on the journals and bearings...
...then turning the correct journal to bottom dead center (BDC), oiling the bore, locating the ring gaps and using the tool to tap the piston in. For ring gap positions I used the ones instructed in Millers book.
I have to say that the installation ring was an excellent tool! I did not have a single problem with any of the pistons. They just smoothly slipped in the cylinders. I pushed the piston in until the bearing contacted the journal.
Final step before placing the cap on the rod was checking that the locating tab on all the bearing faced towards the center of the block.
This meant that the rod had been installed correctly on the piston. Everything was OK in that front so I torqued the cap nuts to 24 ft-lbs. And after a few hours of work, all the pistons were in!
Turning the crank was naturally much harder now but everything still moved smoothly so this job was done!
No comments:
Post a Comment